10/24/2019 Coleman Spas Hot Tub Error Codes
Spaside Readout Modern hot tubs with electronic controls feature spaside keypads with digital readouts. Wondering what your spa is trying to tell you? Below is a list of common error codes from the top manufacturers of control equipment for hot tubs. Note: The control system brand name is usually different from the hot tub brand name. You can often determine the make of the control system by looking inside the spa's equipment area.
Pictured here is a Balboa® control system used in Belize Spas brand. Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. We make no representation as to the accuracy or completeness of this data and are not responsible for errors or omissions. Refer to your owner's manual. Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F.
Status of the heater element is unknown. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F. OH = Over heat. The spa is at a temperature above 108°. Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.
SEoP = Sensor open or disconnected. Heater disabled but the spa is operational.
SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump. PSoL = Pressure switch open with low pump.
PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable.
Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. OHH = Overheat. Spa has shut down. One sensor has detected 118° F at heater. OHS = Overheat.
Spa has shut down. One sensor has detected 110°F. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = Temp sensor malfunction SnA = Spa is shut down. Sensor plugged into jack A is not working.
Snb = Spa is shut down. Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition.
If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected. Could indicate a flow problem. LF = Persistent low flow problems. (Displays on the 5th occurrence of 'HFL' message with 24 hours).
Heater is shut down, but other spa functions run normally. Dr = Inadequate water detected in heater. Dry = Inadequate water detected in heater.
(Displays on third occurrence of 'dr' message). Spa is shut down. Pr = When spa is first actuated, it will go into Priming Mode.
ILOC = Interlock failure - possible pump or ozone spike. (-) =Unknown water temperature. (Displays when first powered up after refill).
Std = Spa operating in Standard Mode. Ecn = Spa operating in Economy Mode. SE = Spa operating in Standard-in-Economy Mode. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp sensor E2 = Shorted hi-limit sensor E3 = Open hi-limit sensor E4 = Shorted flow switch E7 = Improper electrical connection CTI th1/39 = On startup indicates temperature probe problem. Th2/current temperature = On startup indicates temperature probe problem. Th3/39 = On startup indicates water temperature less than 39° F.
OH = Overheating, water over 112° F. System will restart when temp. Hot = Overheating, water over 112° F. System will restart when temp.
HL = High limit switch tripped. Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated.
Do not enter the water. Pressure switch is not working. SN = Non functional high temperature sensor. Heater is deactivated.
Jacuzzi Hot Tubs and Spas The family behind Jacuzzi Hot Tubs & Spas first made an aerating pump for hydrotherapy in the 1950s, and they began manufacturing hot tubs two decades later. By the ‘90s, these hot tubs had expanded into backyard models, and the award-winning company spread out into the international market by the year 2000. The company holds more than 250 patents worldwide, including the first patent in the world for a whirlpool bath. Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi Hot Tubs & Spas is headquartered in. There are several models available for each group size such as the J-495 in the 6+ Person Series. Spa Models Jacuzzi Hot Tubs Company has a great range of Spas, and has been adding models through the years.
Below are some of the more recent Jacuzzi models. The Jacuzzi hot tubs are split into five categories the Jacuzzi J- LX series, Jacuzzi J-500 series, Jacuzzi J-400 series, Jacuzzi J-300 series, and the Jacuzzi J-200 series.
The first custom hot tub cover ever made by was for a Jacuzzi Karma, and we made many of them through the years along with all the Jacuzzi hot tubs. The Cover Guy manufacturers models. We also have a. The Jacuzzi J- 585 hot tub spa is a 6 person hot tub. The J- 585 features four deep bucket seats for the ultimate deep sitting hot tub.
The J-585 also has a very good step to enter the hot tub. You can find the here. The Jacuzzi J- 575 hot tub spa is a 6 person hot tub.
The J- 575 features two deep bucket seats for the and one deep sitting lounge for best relaxation. The J-575 also has a nice step to enter the hot tub. You can find the here. The Jacuzzi J- 470 hot tub spa is a 8 person hot tub. The J- 470 features four deep bucket seats for the ultimate deep sitting hot tub. The J-470 also has a very nice center jet in the hot tub. The Jacuzzi Spa J-465 hot tub spa is a 5 person hot tub.
The J- 465 features two deep bucket seats and one deep lounge for someone to lay back and relax in. The J-465 is a great spa or hot tub with many seat choices. The Jacuzzi Spa J-135 hot tub is a 6 person entry level hot tub. The Jacuzzi Spa J-135 features two deep bucket seats for the and a lounge. The Jacuzzi Spa J-135 has basic jetting making it an entry level hot tub. The Jacuzzi Spa J-280 hot tub spa is a 6 person hot tub. The Jacuzzi Spa J-280 features four deep bucket seats, and basic jetting keeping the cost down.
The The J-280 also has a very good step to enter the hot tub. The Jacuzzi Spa J-355 hot tub is a 4 person tub. The J- 355 features 2 deep bucket seats, one lounge and is a deep sitting hot tub.
The J-355 has a small but good step to enter the hot tub. Great tub for a small family.
The Jacuzzi Spa J-335 hot tub is a 5 person hot tub. The J- 335 features two deep bucket seats and a lounge and is a deep sitting hot tub. The J-335 is an entry level hot tub with some great jetting. The Jacuzzi Spa J-210 hot tub spa is a 6 person hot tub. The J- 210 is a throwback to the original hot tub round design. The jetting is very basic but the atmosphere is great in this social hot tub. The jacuzzi spa J-315 hot tub spa is a 6 person hot tub.
The J- 315 features two bucket seats and a lounge. The J-315 is similar to the J-325 but has more jetting for more water movement. The J-365 jacuzzi hot tub hot tub spa is a 6 person hot tub. The J- 365 features four deep bucket seats and four smaller bench seats. The entry area is small, but the footwell jetting is great.
The Jacuzzi Spa J-385 hot tub spa is a 6 person hot tub. The J- 385 features four deep bucket seats. The J-385 has a large step to enter the hot tub that can be very useful in the evening. The Jacuzzi Spa J-325 hot tub spa is a 3-4 person hot tub. The J- 325 features two deep bucket seats and one deep lounge. The J-325 is one of the smaller backyard hot tubs available.
The Jacuzzi Spa J-495 hot tub spa is an 8-10 person hot tub. The J- 495 features four deep bucket seats and some good bench seating as well to accommodate all your friends. Jacuzzi Hot Tubs and Spa Owners Manuals These are the error codes and display messages that a Jacuzzi Hot Tub may display, along with what they mean and any actions required: Jacuzzi Hot Tubs LX Collection Error Conditions/ Error Messages Message Meaning Action Required COL This only occurs when spa is in Economy mode and indicates a cool condition where temps have dropped 20°F (11°C) below current settings for them. Free download games farm frenzy 3 full version. System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps. No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold.
ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement freeze protection. No action is needed. Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Sn1 Stands for “Sensor 1” and displays when the high-limit sensor is malfunctioning. Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled.
Contact a Jacuzzi hot tubs dealer or a service technician. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning.
Indicates a shorted sensor and the heater is disabled. Contact Jacuzzi hot tubs dealer or a service technician.
FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake.When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed. In both cases, the spa heater will deactivate. Jets pump 1 will likely deactivate, also. Check to see if the water level is below the lowest pillow but above the jets. Add water if needed.2. Check for dirty or clogged filter cartridge.3.
A) Remove filter cartridge in order to purge the air lock from the circulation pump intake. B) Hold a garden hose over filter cartridge wall fitting and utilize a rag to make a seal around hose end. C) Get an assistant to help turn the water on for 30 seconds. Then turn it then turn it off. D) Replace the filter cartridge and verify the solution worked.4.
If circulation pump is not powering on, try cutting off power at the mainbreaker. Turning it on will reset cycle for the circulation pump. After the pump primes itself, the error message should go away.5. Contact dealer or a service technician if problem continues. OH One of the sensors detected that the water in the hot tub is 112°F (44°C). Stands for “Overheat”- and the tub shuts down because water temp is too hot. Low speed jets pump 1 and optional circulation pump (if your spa is equipped so) activates to circulate water through heater.
DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down.2.
Program setting of spa unit for Economy Mode.3. Raise the water temp settings in order to cancel the Summer Logic condition. See “Summer Log” below.3. Shut the power down to the hot tub and contact the dealer or service technician if the problem continues. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa system.
Condition can cause injury or damage to spa and its components. The spa deactivates in this situation. DO NOT GET INTO THE WATER. Contact dealer or a service technician. BLB (Flashes in between water temperature and “blb”) Indicates that the Jacuzzi Hot Tubs needs a new UV bulb.
Purchase new UV bulb from dealer and reset countdown timer. Summer Logic “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather. The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. This setting is not user-programmable. This condition does not kick in until the water temperature climbs to 95°F (35°C).
The spa system’s ability to cool itself down is directly affected by ambient temperatures. Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat.
Jacuzzi Hot Tubs J-400 Error Conditions/ Error Messages Message Meaning Action Required Overheat Protection The water temperature is higher than acceptable safety limits. Filter and circulation pump is activated and the heater is deactivated DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down and reduce thermostat settings. Switch spa to Programmable Mode in order to turn the heater on solely during programmedfilter cycles.
Shut the power down to the hot tub and contact the dealer or service technician if the problem continues. Water is below set temp Condition that provides freeze protection and activates if temps raise to more than 20°F (6°C) cooler than set point of the temperature. Heater will automatically turn on when this happens and stay in this mode until water temperature reaches 15 degrees below set temperature. No action needed. Communication Error Communication between circuit board and control panel is malfunctioning.
Contact the dealer or service technician if the problem continues. Pump does not operate Water flow in spa is insufficient or the flow switch is malfunctioning. Check for a clogged filter or low water levels.
If buzzing sound or lack of sound is detected, cut off the water to the hot tub – may indicate that pump is notproperly primed. Contact the dealer or service technician if the problem continues.
Freeze Protection The spa system has detected a potential freeze condition. The heater and jets pumps continue running until the spa unit is out of the danger zone. No action needed.Note: It isn’t possible to control the pumps manually while the Freeze condition is running. You can push a button on the Control Panel to make the error message go away, but the message will return if the spa unit is still in Freeze condition five minutes later. This condition often occurs when filling the spa with water since tap water is usually cold.
Emergency Shutdown The system has detected that spa water temperatures are above acceptable safety limits. The spa is deactivated for potential damage to spa and its components. DO NOT GET INTO THE WATER. Contact the dealer or service technician. Open Sensor Means temperature sensor is malfunctioning; heater is taken offline automatically when this happens. Do not attempt to service on your own. Contact the dealer or service technician.
Shorted Sensor Means temperature sensor is malfunctioning; heater is taken offline automatically when this happens. Do not attempt to service on your own. Contact the dealer or service technician. Open Sensor (Hi-Limit) The hi-limit temperature sensor is malfunctioning; heater is taken offline automatically when this happens. Do not attempt to service on your own. Contact the dealer or service technician. Shorted Sensor (Hi-Limit) The hi-limit temperature sensor is malfunctioning; heater is taken offline automatically when this happens.
Do not attempt to service on your own. Contact the dealer or service technician. Start-up Malfunction Flow switch is malfunctioning. System is disabled in this event and indicates a shorted or closed flow switch when system is started up. Do not attempt to service on your own. Contact the dealer or service technician. Open Flow Switch Means that the switch is malfunctioning and staying open, the filter cartridge for the circulation pump is dirty or an air lock issue occurred at the intake for the circulation pump intake.
Heater is automatically disabled in this event, and the filter/circulation may be disabled, too. Contact the dealer or service technician.
Closed Flow Switch Means that the switch is malfunctioning and staying closed. Heater is automatically disabled in this event, and the filter/circulation may be disabled, too.
Contact the dealer or service technician. Malfunction Communication between audio system and the control panel is malfunctioning. Power down the spa.
Wait three seconds and then restart the spa to see if error clears up. Contact the dealer or service technician if the problem continues. Blinking Heater Icon Icon flashes on and off to let you know that the temperature sensor has detected either a temperature difference of-20°F (6°C) difference between set and actual temperature ortemp above 112°F (44°C). Can also mean the hi-limit temp sensor is detecting temp above 116°F/46°C. Please Check Filter Message displays when the reminder time of the filter has expired. Means that the ProClarity/Proclear needs to be cleaned or replaced.
Remove the filter/debris bag for and clean or replace. Feature not Installed Message displays when you try to activate features that are not installed.
To clear the message press button D toreturn to the Main Menu Press the D button to clear the message and return to the main menu. Jacuzzi Hot Tubs J-300 Error Conditions/ Error Messages Message Meaning Action Required COL This only occurs when spa is in Economy mode and indicates a cool condition where temps have dropped 20°F (11°C) below current set temps.
System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps. No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement freeze protection. No action is needed.
Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Sn1 Stands for “Sensor 1” and displays when the high-limit sensor is malfunctioning. Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled. Contact dealer or a service technician. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Indicates a shorted sensor and the heater is disabled. Contact dealer or a service technician.
BLB (Flashes in between water temperature and “blb”) Indicates that spa needs a new UV bulb. Replace UV bulb (you can get one from your authorized Jacuzzi dealer).
Reset the countdown timer when finished. FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake.When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed. In both cases, the spa heater will deactivate. Jets pump 1 will likely deactivate, also. Check to see if the water level is below the lowest pillow but above the jets. Add water if needed.2. Check for dirty or clogged filter cartridge.3.
A) Remove filter cartridge in order to purge the air lock from the circulation pump intake. B) Hold a garden hose over filter cartridge wall fitting and utilize a rag to make a seal around hose end. C) Get an assistant to help turn the water on for 30 seconds. Then turn it then turn it off.
D) Replace the filter cartridge and verify the solution worked.4. If circulation pump is not powering on, try cutting off power at the mainbreaker. Turning it on will reset cycle for the circulation pump. After the pump primes itself, the error message should go away.5. Contact dealer or a service technician if problem continues.
OH One of the sensors detected that the water in the hot tub is 112°F (44°C). Stands for “Overheat”- and the tub shuts down because water temp is too hot. Low speed jets pump 1 and optional circulation pump (if your spa is equipped) activates to circulate water through heater. DO NOT GET INTO THE WATER. Take off the spa cover to allow the water to cool down.2. Program setting of spa unit for Economy Mode.3. Raise the water temp settings in order to cancel the Summer Logic condition.
See “Summer Log” below.3. Shut the power down to the hot tub and contact the dealer or service technician if the problem continues. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa system. Condition can cause injury or damage to spa and its components. The spa deactivates in this situation.
DO NOT GET INTO THE WATER. Contact dealer or a service technician. Summer Logic “Summer Logic” occurs when the actual water temp for the spa climbs to 2°F (1°C) above set temperatures and is more likely in extremely hot weather. The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. This setting is not user-programmable. This condition does not kick in until the water temperature climbs to 95°F (35°C). The spa system’s ability to cool itself down is directly affected by ambient temperatures.
Very hot summer ambient temperatures can prevent the spa unit from cooling because it’s insulated construction is designed to minimize operating costs and hold in heat. CF The clean filter timer has expired.The message will flash between “CF”and the water temperature. The countdown timer for the Change Filterfeature needs to be reset (page 31). New filters can be purchasedfrom a local Jacuzzi dealer. The spa filters need to becleaned or replaced. Jacuzzi Hot Tubs J-200 Error Conditions/ Error Messages Message Meaning Action Required COL This only occurs when spa is in Economy mode and indicates a cool condition where temps have dropped 20°F (11°C) below current set temps. System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps.
No action required.Note: this condition often occurs when filling the spa with water since tap water is usually cold. ICE This only occurs when spa is in Economy mode and stands for “Ice;” means the system has detected a potential condition for freezing and will cause the system to implement freeze protection. No action is needed.
Jet pumps 1 and the heater activate automatically to bring the temp to 15°F (8°C) of the settemps.Note: this condition often occurs when filling the spa with water since tap water is usually cold. Sn1 Stands for “Sensor 1” and displays when the high-limit sensor is malfunctioning. Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled.
Contact a Jacuzzi hot tubs dealer or a service technician. Sn2 Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Indicates a shorted sensor and the heater is disabled. Contact a Jacuzzi hot tubs dealer or a service technician. FL1 or FL2 (Flashing) When FL1 code starts flashing it means the flow switch is malfunctioning and stuck open-likely because of a dirty filter or because there is an air lock problem at the circulation pump intake.When FL2 code starts flashing it means the flow switch isn’t working and it is stuck closed.
In both cases, the spa heater will deactivate. Jets pump 1 will likely deactivate, also. Check to see if the water level is below the lowest pillow but above the jets.
Add water if needed.2. Check for dirty or clogged filter cartridge.3. Jets pump 1 needs an “air lock” purge; do this by loosening up for a few seconds the upper pump head drain screw. This releases trapped air, and when finished, retighten the screw to the drain. ONLY USE FINGER TIGHTENING METHOD!4.
Contact dealer or a service technician if problem continues. OH One of the sensors detected that the water in the hot tub is 112°F (44°C). Stands for “Overheat”- and the tub shuts down because water temp is too hot. Low speed jets pump 1 and optional circulation pump (if your spa is equipped) activates to circulate water through heater. DO NOT GET INTO THE WATER. Contact a Jacuzzi hot tubs dealer or a service technician. – – – The water temp has raised above acceptable safety limits and triggered the safety “Watchdog” program of the spa system.
Condition can cause injury or damage to spa and its components. The spa deactivates in this situation. DO NOT GET INTO THE WATER. Contacta Jacuzzi hot tubs dealer or a service technician. BLB (Flashes in between water temperature and “blb”) Indicates that spa needs a new UV bulb. Replace UV bulb (you can get one from your authorized Jacuzzi dealer). Reset the countdown timer when finished.
Untitled Document Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. Status of the heater element is unknown. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.
OH = Over heat. The spa is at a temperature above 108°. Do not use spa when temperature is flashing or the OH message is displayed. HLoH = Hi Limit Over Heat. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. SEoP = Sensor open or disconnected. Heater disabled but the spa is operational.
SESH = Sensor short, nonfunctional. Heater disabled but the spa is operational. PSoC = Pressure switch open with circulating pump.
PSoL = Pressure switch open with low pump. PSoH = Pressure switch open with high pump. ToE = Time out error. Rare system error. Spa unusable.
Balboa pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. OHH = Overheat. Spa has shut down. One sensor has detected 118º Fat heater.
OHS = Overheat. Spa has shut down. One sensor has detected 110ºF. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = Temp sensor malfunction SnA = Spa is shut down. Sensor plugged into jack A is not working. Snb = Spa is shut down.
Sensor plugged into jack B is not working. SnS = Sensors out of balance. If alternating with temp, may be temporary condition. If display shows only this message (blinking) spa is shut down. HFL = Substantial difference between temperature sensors detected.
Could indicate a flow problem. LF = Persistent low flow problems.
(Displays on the 5th occurrence of 'HFL' message with 24 hours). Heater is shut down, but other spa functions run normally. Dr = Inadequate water detected in heater. Dry = Inadequate water detected in heater. (Displays on third occurrence of 'dr' message). Spa is shut down. Pr = When spa is first actuated, it will go into Priming Mode.
ILOC = Interlock failure - possible pump or ozone spike. (-) =Unknown water temperature. (Displays when first powered up after refill). Std = Spa operating in Standard Mode. Ecn = Spa operating in Economy Mode.
SE = Spa operating in Standard-in-Economy Mode. Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp sensor E2 = Shorted hi-limit sensor E3 = Open hi-limit sensor E4 = Shorted flow switch E7 = Improper electrical connection CTI th1/39 = On startup indicates temperature probe problem. Th2/current temperature = On startup indicates temperature probe problem. Th3/39 = On startup indicates water temperature less than 39° F. OH = Overheating, water over 112° F.
System will restart when temp. Hot = Overheating, water over 112° F. System will restart when temp. HL = High limit switch tripped.
Dream Maker Hot Tubs OH = Overheat 108° F, spa is deactivated. Do not enter the water. Pressure switch is not working. SN = Non functional high temperature sensor.
Heater is deactivated.
. Because this is a portable, inflatable hot tub, you don’t have to install a large in-ground hot tub that requires thousands of dollars and the services of a plumber and an electrician. The tub can be moved inside during cold weather and taken with you when you travel or go on vacation. It sets up easily and quickly, and no extra tools are needed. The Coleman Lay-Z Spa is easy to get into; just step over the side.
You really don’t need steps. The tub fills quickly with a standard garden hose, although you do need to allow at least 24 hours for the water to reach the maximum 104-degree-temperature.
The heater and pump don’t make a lot of noise, although the bubbles do create more of a vacuum cleaner sound. You’re going to find this with any hot tub, no matter how expensive, but this can add to the soothing effect. The Coleman Company offers greater customer service. The package includes a refrigerator magnet with the toll-free customer service phone number on it. Owners report customer service is friendly and helpful. The Lay-Z Spa also can’t be left set up outside in temperatures under 40 degrees Fahrenheit, which means that it might not be the best choice for people who are looking for something to use in the winter and live in the coldest US states. The bubbles in the Coleman Lay-Z Spa are not like hard water jets, but more like a soft massage.
If you’re looking for those pounding jets, you won’t find that here, but you might enjoy the gentle bubbles. The safety of the cover must be an issue, too. The manual says it’s not a “safety cover.” If you have small children, you’ll want to be sure the tub is in a secure setting where a child could get into it, such as a fenced-in area with a lock on the gate or in a locked garage. The heater doesn’t run when the bubbles are on like many other inflatable hot tubs. Thinking to buy it? You can add it to your cart by clicking the following button while you make a decision. Coleman SaluSpa Inflatable Hot Tub: 4-Person With about 90-100$ cheaper than Lay Z Spa, Saluspa can accommodate only 4 people and have a water capacity of 192-gallons.
Coleman SaluSpa 4 Person Portable Hot Tub Inflatable and portable hot tub that seats 4 people. You can take it with you on your vacations or relax at home. It has massage jets and a cushioned floor, making it easy for you to unwind. The hot tub inflates within minutes and the rapid heating system quickly heats the water up to a soothing 104 degrees with 60 surrounding air jets. Hot temperature is perfect for soothing sore muscles or lounging after a long day and the digital control panel lets you adjust the temperature without having to get out of the tub.
The walls are made of durable 3-ply PVC and have sturdy I-Beam construction that allows you to sit on the sides of the spa thanks to the superior structural stability. There are 2 handles built into the sides for easy transportation. This package also includes a chemical floater to keep your spa clean, a twin pack of filter cartridges, and an inflatable cover to keep your water warm when you’re not using it.
Enjoy the luxury of a hot tub in your house by yourself, with friends, or as a romantic treat with the Coleman Inflatable Miami Spa. Thinking to buy it?
You can add it to your cart by clicking the following button while you make a decision. Coleman Hot Tub Prices The Coleman Lay-Z Spa is priced under $500 and SaluSpa is priced under $400, which is quite economical for the features it offers. You might want to compare it to the Intex PureSpa, which is generally priced about $30 less and appears to have lesser costs associated with replacing filters.
Coleman Lay Z Spa Coleman Sluspa 4 person: Coleman Pools Vs Intex Pools Both of these hot tubs are an excellent choice and you won’t go wrong if you wanted to buy either one. Coleman Lay Z Spa has a higher average consumer rating than the Intex hot tub. Coleman Lay-Z Spa and Intex Purespa have same inflated Size of 77″ diameter x 28″ height. But Coleman Lay -z spa 254 Gal have more water capacity than Intex 210 Gal. It can accommodate 2 more people than Intext PureSpa. So if you’re looking for a 6 person hot tub, you definitely should go with Coleman lazy spa.
If you can accommodate in 4 people capacity. You have two option Intex PureSpa or Coleman Saluspa. Unlike the Coleman Slauspa, Intex model comes with an entire set of accessories that are necessary for any tub. This includes extra filter cartridges, chemical testing strips, and a chlorine dispenser. Coleman Hot Tub Problems Coleman Lazy Spa Error Codes There may be a number of reasons why your heater/pump is displaying an error code. The following is a list of error codes, the reason behind them and how they can be solved.
Lay Z Spa Heater Trips Out When you press the heater button, it blows trip switch? With power disconnected, take off the cover, take off heater leads. Take a picture or write a note to remember where they go.
Coleman Inflatable Hot Tub
If you turn it on and doesn’t blow fuse it’s a bad heater element. You may need a replacement. Tip: if you are not using your spa for a period of time, then take your filters out of the pump/heater unit and keep them in a dry place, just remember to put them back in before you turn your filter pump back on and bleed the system of air again before you use your Spa again. Keep your tub clean as the debris (hair strands, gravel, leaves, grass etc) stuck in the pump may cause your Bestway Heater Pump to restrict from working properly. Coleman Hot Tub Parts Since Coleman Lay z spa hot tub is the best of the two with over 1100 customer reviews on Amazon. We’ll get into the details of this product. Coleman Lay Z Spa Parts Lay-Z-Massage System The highlight of the Coleman Lay-Z Spa Inflatable Hot Tub is the Lay-Z-Massage System, a hydromassage system powered by 120 bubble jets.
Rapid Heating System This sets up the hot tub water temperature quickly, approximately 2-3 degrees per hour, or about 24 hours to raise the water temperature up to the maximum 104 degrees. You can get it to the temperature in only six hours if you use hot water as reported by many users. However, it may cost you some extra bucks. Digital Control Panel Sitting on top of the large green egg-shaped device, this controls all the features of the hot tub, activates the bubbles, controls the temperature, and locks the control panel as a child-safety feature.
A review of the control panel buttons shows the following: A review of the control panel buttons shows the following:. Auto-lock: There is a five-minute auto lock on the control panel. To release the controls, hold this button down for three seconds. On the left and right sides, there are buttons marked with an up arrow and a down arrow.
Coleman Spas Hot Tub Walmart
Press either one to increase or decrease the water temperature. The button marked with a sunray activates the heating system. The pump will heat the spa water until the temp reaches 1 degree higher than the set temp. After the current water temp drops 2 degrees below the set temp, the heating system will restart. When the light above the heat button is red, the system is activated.
When the light is green, the water is at the set temp and the heating system is at rest. The button with the three bubble sprays activates the bubble massage system. Button on the bottom left marked F/C, toggles between Fahrenheit and Celsius temperature readings. To the right of the temperature, a toggle button is the water filter button that turns the water filter pump on and off.
When activated, the light above the water filter button will turn red. Integrated Water Filtration The filtration system keeps your water clean and comes with a twin pack of two extra filters.
When the heating system is activated, the filtration system will automatically restart. When the heating system is turned off, the filtration system will continue to operate.
Your hot tub will have come with a filter however it is important to wash these out under the tap and from time to time you should replace them with a new one. You can Seats: There are no built-in seats, but you sit on a soft, cushioned bottom, similar to sitting on an air mattress. DVD detailing spa setup and maintenance. Coleman Hot Tub Accessories. Floating: Add some color and light to your spa with the Lay-Z-Spa Hot Tub & Pool LED Floating Light.
A floating lighting device that will brighten up your spa and add some mood lighting in the evening. Check it out here. Hot tub chemicals: Keeping your water appropriately tested and using the correct chemicals is very important. Check a complete guide about. Mosaic print pool liner with cushioned floor and convenient drain valve.
Insulated Cover: When you aren’t using the tub, the cover that is insulated with an aluminum foil coating maintains heat and keeps out debris. Round leather-type piece fits inside the cover and inflates to provide greater insulation. Coleman.: This small plastic device floats in the water and easily dispenses the necessary chemicals. This is usually included with the hot tub.
Air-Padded Ground Cloth: This is included to protect the bottom of your spa. Coleman Hot Tub Filters: To filter out this debris using a filter, keep your hot tub pump in good shape and help prevent any damage. You may need to replace from time to time with a new one. You can Coleman Spa Hot Tub Manual There is a six-month warranty on the spa liner and a one-year warranty on the spa pump. Check Coleman & Coleman Feel free to share your thoughts in comments and share this post with your friends and social circle ?.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |